![]() ![]() ![]() Oh, ill re-post my question if there is a better threadĪnonymous Fri Dec 29 03:26:25 2017 No.1304390Īnyone sell their printer? I have a custom one and it's too big for me now that I moved to a smaller place. Is there any free/low cost shipping distributor that is open right now?Īnonymous Fri Dec 29 03:00:53 2017 No.1304384 I dont know if the typical resistor setup works, but my common NPN sensor shouldn't have any issue with that. Is there a better method than this? most of the other boards have 5v on the endstop pins rather than 3v on the duet. I have lots of resisters and one, untested/Idontknowhowtoreadsignaldiodes diode and need to find a replacement. Moved to duet, found out my z probe sensor needs to now work with 3v logic.Įverything is setup and good other than the probe, but all the online distributors with samples are closed until January for a BAT43 diode that they recommend Oops I wasn't paying attention and now it's too late to delete. A little upset at the spot under the tail, but i was thinking of painting anyways.Īnonymous Thu Dec 28 23:45:57 2017 No.1304321 ![]() ![]() Would have looked pretty sweet in two tone. I really wish i had some white pla left over. >what programs do you make your own files withīegin with a roll of known brand PLA before moving to more demanding materials. >why do my prints look like shit, visual troubleshooting When【Wifi Antenna 110】is clamped into base on the back of the 3D printer, rotate it 45° counterclockwise to ensure it is completely fixed./3dpg/ - 3D Printing General Anonymous Thu Dec 28 20:10:32 2017 No.1304229Īdditive Manufacturing Technologies:3D Printing, Rapid Prototyping, and Direct Digital Manufacturing, Gibson Rosen Stucker Note: When【Motherboard Platform Controls FFC】passing through Z-axis, in order to prevent unnecessary line occlusion during the operation of the 3D printer, it is necessary to fold a triangle in the middle of【Mainboard Platform Control FFC】, and pass it through Z-axis from the gap.Ĭonnect one end of the to the, fold the middle part of the cable as well and pass it through the Z-axis from the gap for later use.įix the 3D printed【Cable Clip】on the X-axis, so that the 【Heated Bed Cable]】can be stretched.Ĭonnect one end of【Wifi Antenna 110】 to the port on 【CPU】, and the other end is clamped into the base on the back of the 3D printer. Be sure to lock the connection point to prevent it from falling off.Ĭonnect The Motherboard Platform Control FFC to the Adapter PlateĬonnect The【Motherboard Platform Control FFC】to the【Motherboard】 Overall Connection of Z-axis Wiring HarnessĬonnect one end of the Y/Z-axis limit Switch adapter cable (107) to the Adapter Plate and the other end to the mainboard.Ĭonnect the Y/Z-axis Limit Switch Adapter Cable to the MainboardĢ.4 Connect Mainboard platform Control FFCĬonnect one end of the on the Adapter Plate, and connect the other end to the mainboard. Insert the Z-axis motor cable into the motor below the Z-axis profile (4pin Socket in Yellow), and insert the Z-axis cable into the mainboard (yellow).Ĭonnect Z-axis motor Cable to Motherboard and Motor Overall Connection of Y-axis Motor Wiring harness Insert both the Y-axis motor cable (103) and the Y-axis reset switch cable (104) into the Adapter Plate (Red socket) Mount the Z-axis adapter plate and the base, and fix them with the No.48 screws After the Z-axis adapter plate base is fixed to the Z-axis, align the metal-moving ship-shaped nut with the threaded hole. Note: Before fixing the baseplate onto the Z-axis, unscrew the metal-moving ship-shaped nut. Clamp Z-axis adapter plate base to Z-axis groove and fix it with the No.48 nut. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |